One of the owners of Velocity Tech Solutions and the CIO, AKA Best Geek Ever is looking of ways to help people get through the “SERVER HELL” of setting up raid. So often a tech will walk into a job where someone else set up the server and all is good in the world until it crashes. They then enter “server hell” and since each machine is different, server hell can be a long hard road.
For those having to set up a raid array on a Dell Poweredge 2850 Server, Kay Winchell has made it a bit easier. Read Below:
RAID, or Redundant Array of Independent Disks, is a term used to describe a data storage method that can manage data among multiple hard disk drives on a server . The main reason a Raid Array is used is for performance and redundancy, the benefits of which depend on the type of Raid chosen. The three most common types of Raid Arrays for servers are Raid 0, Raid 1, and Raid 5.
Raid 0, which is also called Striping, provides for higher performance and zero redundancy. The Raid controller writes data across all drives in the array and reads and writes to multiple disks at the same time. Speed is enhanced, however, if one hard drive in the array fails, all data is usually lost.
Raid 1, which is also called Mirroring, provides for high redundancy, but zero increase in performance. Each hard drive is paired with another, one being a copy, or mirror, of the other. If one hard drive fails, the paired drive contains the same data. To set up Raid 1, the server must have at least two hard drives.
Raid 5, which is also called Stripe Sets with Parity, has a mix of performance and redundancy benefits. Data is written to all of the drives in the array and parity data is written to all of the drives in the array as well. The result is an increase in performance over mirroring while maintaining redundancy. If a hard drive in the array fails, a new drive can be added and the array repairs itself while the system continues to operate normally. For this reason, Raid 5 is the array of choice for most servers with three or more disks.
Here are the instructions to set up a Raid Array for the Poweredge 2850 Server. Please be aware that the instructions below are for setting up an array in a new server, not for adding drives to an array.
Step 1: Power on the server. The machine will go through POST (Power On Self Test) at which time hardware components are identified and checked. Step 2: The server will now start to boot. A prompt will come up that says: Dell Poweredge Expandable RAID Controller Copyright © American Megatrends Inc. Press <Ctrl M> to run configuration utility.
Step 3: After pressing <Ctrl M>, the Management Menu appears. The first item on the Management Menu is Easy Configuration. Select Easy Configuration.
Step 4: A screen now appears with a listing of your hard drives. Press the SPACE bar for each drive you want to configure. Press Enter when finished selecting your drives.
Step 5: Now you will choose your span, which is how many drives you want to configure into your array. Use the spacebar to select your span. Press F10 when finished selecting your span. The reason you select a span is because multiple Raid Arrays can be set up within your drives. For instance, many administrators set up an array with the first two drives for the OS, with a second array for data.
Step 6: A Screen now appears for Choose your Raid Level. Depending on how many drives you have selected in your span, the system will offer you various options of Raid 0, 1, or 5. Arrow up or down and select your Raid level. Press Enter to accept.
Step 7: At the prompt of Escape to Save Configuration, press yes. Your Raid Array is now configured.
Anne Tarantino via Kay Winchell
Velocity Tech Solutions
Wednesday, September 29, 2010
Monday, September 27, 2010
Dell Poweredge 2850/2800/1850 Batt/Mem Error
So, hardware isn’t the spice of life, and writing about is isn’t near as fun and writing about something controversial where everyone and their brother gets worked up and starts spewing their opinions. But, It’s what I do and honestly, it is kind of fun in a non Geeky, but Geeky kind of way.
For you people that have Dell PE2800, 2850, 1850 servers, you may be experiencing a mem/batt error. The error can be a little confusing because it can be any piece of the raid kit, Dell part number H1813 (key, battery, or memory stick). To make it even more confusing, you can change out all of those parts and still have the same error. If that persists, your riser card is more than likely failing. The riser cards for those machines have multiple part numbers.
This is just a little Geeky FYI for those that are pulling their hair out looking for answers.
You can always call me at (888)784-2088 or check out our web page at www.velocitytechsolutions.com
Hope this helps someone out there!
Anne
For you people that have Dell PE2800, 2850, 1850 servers, you may be experiencing a mem/batt error. The error can be a little confusing because it can be any piece of the raid kit, Dell part number H1813 (key, battery, or memory stick). To make it even more confusing, you can change out all of those parts and still have the same error. If that persists, your riser card is more than likely failing. The riser cards for those machines have multiple part numbers.
This is just a little Geeky FYI for those that are pulling their hair out looking for answers.
You can always call me at (888)784-2088 or check out our web page at www.velocitytechsolutions.com
Hope this helps someone out there!
Anne
Friday, September 24, 2010
Used Networking Equipment; It Ain't so Bad
My how the recession has changed the way we think and the way we buy. Not just in our personal lives, but also business spending.
My prior life was running call centers, my middle name was production. Everything was about production. Production meetings usually produced nothing and were about as exciting and watching paint dry. Honestly, it was fun when we were down because to watch people run like their pants were on fire saying “we’re losing production” and having no clue what to do except hover over the tech that was trying to figure out how to fix the issue.That lead to always spending ridiculous amounts of money on new servers,switches and everything else that lost more value than driving a new giant SUV off the lot.
Fast forward to post 2007. Unemployment is high, foreclosure is high, gas is high, spending; non existent.
Thankfully, my life as a call center Nazi is over. I do keep in touch with many of those people who are now my customers. They have servers and equipment that are at 5 or so years old and they keep buying servers and server parts and are thankful to keep that stuff running.
Dell Power edge Servers really made a huge impact on the networking market over the past 10 years or so. They appealed to the small and medium market and were more affordable than the larger enterprise class manufacturers like HP and IBM. So many businesses were buying Power Edge Servers and every 3 years, they were getting the latest and greatest Dell Power Edge Servers. It seemed to be a sign of success. You could run your equipment lease along with your car lease and in one month you could have the Expedition AND the big beefy servers. Oh what fun it was to play with those new toys.
So, now instead of spending $500,000 on a house, we’re back to $150,000. Instead of $50,000 on a car, we’re looking at $15,000 and for our IT equipment, we’ve gone from $100,000 to $10,000. All still with warranties, still reliable.
Suddenly, an older smaller home, a smaller used car and used IT equipment, ain’t so bad.
My prior life was running call centers, my middle name was production. Everything was about production. Production meetings usually produced nothing and were about as exciting and watching paint dry. Honestly, it was fun when we were down because to watch people run like their pants were on fire saying “we’re losing production” and having no clue what to do except hover over the tech that was trying to figure out how to fix the issue.That lead to always spending ridiculous amounts of money on new servers,switches and everything else that lost more value than driving a new giant SUV off the lot.
Fast forward to post 2007. Unemployment is high, foreclosure is high, gas is high, spending; non existent.
Thankfully, my life as a call center Nazi is over. I do keep in touch with many of those people who are now my customers. They have servers and equipment that are at 5 or so years old and they keep buying servers and server parts and are thankful to keep that stuff running.
Dell Power edge Servers really made a huge impact on the networking market over the past 10 years or so. They appealed to the small and medium market and were more affordable than the larger enterprise class manufacturers like HP and IBM. So many businesses were buying Power Edge Servers and every 3 years, they were getting the latest and greatest Dell Power Edge Servers. It seemed to be a sign of success. You could run your equipment lease along with your car lease and in one month you could have the Expedition AND the big beefy servers. Oh what fun it was to play with those new toys.
So, now instead of spending $500,000 on a house, we’re back to $150,000. Instead of $50,000 on a car, we’re looking at $15,000 and for our IT equipment, we’ve gone from $100,000 to $10,000. All still with warranties, still reliable.
Suddenly, an older smaller home, a smaller used car and used IT equipment, ain’t so bad.
Subscribe to:
Posts (Atom)